近五年发表SCI期刊论文19篇，其中中科院1区9篇。

[1] Pengbing Zhao, Jin Huang*. Laser sintering process optimization of microstrip antenna fabricated by inkjet printing with silver-based MOD ink. Journal of Materials Processing Technology. 2020, 275, 116347: 1-15. (IF: 6.7)

[2] Pengbing Zhao*, Chuan Xiong, Zheng Gao, Xiang Liu, Yanbin Zeng. Design and Experiment Investigation on Soft Grippers with Modular Variable Stiffness Structure. Micromachines, 2024, 15, 88: 1-19. (IF: 3.0)

[3] Hongxiao Gong, Pengbing Zhao*. Generation of neutral droplets via waveform optimization for stable electrohydrodynamic drop-on- demand printing. Journal of Manufacturing Processes, 2024, 112: 103-111. (IF: 6.1)

[4] Hongxiao Gong, Jin Huang*, Pengbing Zhao*. Additive Manufacturing for Terahertz Metamaterials on the Dielectric Surface based on Optimized Electrohydrodynamic Drop-on-demand Printing Technology. ACS Applied Materials & Interfaces, 2024, 16, 4222-4230. (IF: 8.3)

[5] Chaoyu Liang , Jin Huang*, Pengbing Zhao. Nano-borosilicate glass-silica ceramic material jetting technology for additive manufacturing of multilayer LTCC substrates. Journal of Manufacturing Processes, 2024, 123: 20-27. (IF: 6.1)

[6] Fanbo Meng, Jin Huang*, Bu Ping, Pengbing Zhao. Intelligent control system for 3D inkjet printing. Journal of Intelligent Manufacturing, 2024, 35: 575-586. (IF: 8.3)

[7] Chaoyu Liang , Jin Huang*, Pengbing Zhao. Research on material jetting fabrication and dielectric constant calculation of LTCC based on silica-borosilicate glass. Materials Today Communications, 2024, 40: 109741. (IF: 3.7)

[8] Hongxiao Gong, Jin Huang*, Pengbing Zhao. Research on the printing mechanism of electrohydrodynamic satellite-free droplets in pulsed voltage. Journal of Manufacturing Processes, 2023, 101: 300-310. (IF: 6.1)

[9] Chaoyu Liang , Jin Huang*, Pengbing Zhao. Additive manufacturing of low-temperature co-fired ceramic substrates and surface conductors based on material jetting. Additive Manufacturing, 2023, 78: 103856. (IF: 10.3)

[10] Jianjun Wang*, Jin Huang*, Chaoyu Liang, Pengbing Zhao. Actuation waveform auto-design of drop-on-demand inkjet for ejection droplet without satellite. Journal of Manufacturing Processes, 2023, 102: 910-920. (IF: 6.1)

[11] Chaoyu Liang, Jin Huang*, Pengbing Zhao. Three-dimensional inkjet printing and low temperature sintering of silica-based ceramics. Journal of the European Ceramic Society, 2023, 43: 2289-2294. (IF: 5.8)

[12] Yupeng Yang, Yuzhe Gao, Pengbing Zhao, Xiaocong He*. Simultaneous measurement of local current and temperature distributions in proton exchange membrane fuel cells with dead-ended anode. Applied Thermal Engineering, 2023, 230: 120728. (IF: 6.1)

[13] Jianjun Wang*, Jin Huang, Pengbing Zhao. Waveform Design Method for Piezoelectric Print-Head Based on Iterative Learning and Equivalent Circuit Model. Micromachines, 2023, 14, 768. (IF: 3.0)

[14] Fanbo Meng, Jin Huang*, Pengbing Zhao. Closed-loop optimized nanometal sintering method. Journal of Manufacturing Processes, 2020, 59: 403-410. (IF: 6.1)

[15] Fanbo Meng, Jin Huang*, Pengbing Zhao. Multi-sensor feedback control for the flash sintering of printed nano-silver ink. Journal of Manufacturing Processes, 2020, 53: 356-363. (IF: 6.1)

[16] Yupeng Yang, Pengbing Zhao*. Numerical and experimental investigations on intense pulsed light sintering of silver nanoparticle inks for printed electronics. International Journal of Thermal Sciences, 2022, 176: 107507. (IF: 4.9)

[17] Yupeng Yang, Haijuan Jia, Pengbing Zhao, Xiaocong He*. Overall and local effects of operating parameters on water management and performance of open-cathode PEM fuel cells. Applied Energy, 2022, 315: 118978. (IF: 10.1)

[18] Jiaying Zhang, Jin Huang*, Pengbing Zhao. Analysis Method of Bending Effect on Transmission Characteristics of Ultra-Low-Profile Rectangular Microstrip Antenna, Sensors, 2022, 22: 602. (IF: 3.4)

[19] Lei Han, Pengbing Zhao, Hongxing Zheng*. Tightly Coupled Ultra-Wideband Phased-Array Implemented by Three-Dimensional Inkjet Printing Technique. Electronics, 2022, 11: 3320. (IF: 2.6)